Extron CrossPoint 450 Plus 3232 Matrix Switcher driver for Windows 7 - Extron CrossPoint 450 Plus 3232 Matrix Switcher d

Extron CrossPoint 450 Plus 3232 Matrix Switcher 2.03

Extron CrossPoint 450 Plus 3232 Matrix Switcher driver from Extron for OS Independent

Extron CrossPoint 450 Plus 3232 Matrix Switcher driver from Extron for OS Independent

Publisher review for Extron CrossPoint 450 Plus 3232 Matrix Switcher 2.03:

Before install Extron CrossPoint 450 Plus 3232 Matrix Switcher 2.03you should set a system restore point, to make sure you can rollback to your original driver in case you accidentally install another driver or select the driver for another version of the operating system.

Also, do not forget to check with our site as often as possible for new version of Extron CrossPoint 450 Plus 3232 Matrix Switcher . We recommend to always use most recent version of a driver.

Fixes/Corrections:- Corrected a phantom switching condition – When controlling the matrix primarily through remote control and then making breakaway switches (audio only or video only) from the front panel control buttons, the switcher would recall from memory a previously-executed crosspoint tie. This has been corrected.
- Corrected the Command Response Tags in VERBOSE Mode. Command responses for queries as to the switcher’s state now return tags when the IP and RS-232 ports are set to VERBOSE mode 2 or 3 (Response Tags).
Note: If “tagged responses” is enabled, all read commands will return the constant string plus the data, like setting the value does. Verbose mode provides unit responses when commands are issued through another control port or front panel control.
- Corrected the SIS Read Commands for Input Tie(s). SIS read commands “&”, “%”, “#” and “$” now respond with the input number only when the control port set to verbose mode 2 or 3 (tagged responses).
- Corrected the SIS Read Command for Presets. SIS read command for presets did not have tags assigned for Verbose modes 2 and 3. This has been corrected.
- Corrected the SIS Command for Input Sync. SIS read command for Input sync (LS) did not have tags assigned for Verbose modes 2 and 3. This has been corrected.
- Corrected the SIS Command for System Status Request. SIS command for system status request did not have tags assigned for verbose modes 2 and 3. This has been corrected.
- Corrected the SIS Command for Viewing Output Mutes. SIS command for viewing output mutes formerly had a “garbage tag” assigned for verbose modes 2 and 3. This has been corrected.
- Corrected the front panel response when a third party control is active. In prior revisions, the switcher did not respond correctly when changes were made with a third party control system. Commands were executed but the front panel View response was incorrect.
For example: When the switcher was reset (Esc ZXXX) using Telnet, the switcher front panel did not update pending ties and continued to show the previous ties (using the View button) until another input was selected and the tie viewed again. This has been corrected.
- Corrected the Absolute Reset Command “Esc ZQQQ (cr)” and Press and hold the Reset button until the Front Panel I/O buttons blink twice (for 3232 without reset LED) then immediately press and release again (Mode 5 in other models) – In prior firmware revisions, the command to reset the switcher, Esc ZQQQ (absolute), gave the correct response but did not execute the full reset; it only reset the IP related settings. Correct operation of this function has been resolved, Absolute reset clears all ties and presets, resets all audio gains and volumes, RGB delays, Rooms and I/O groups to the default values. It also resets the serial control port back to default conditions (RS-232, 9600 baud, 8 data bits, 1 stop bit, no parity, no flow control).
- Corrected the Reset the Whole Switcher Command “Esc ZXXX (cr)” and Press and hold both I/O buttons while applying power to the switcher – In prior firmware revisions, the command to reset the whole switcher, Esc ZXXX does not include resetting the serial port back default conditions. It only clears all ties and presets, resets all gains and volumes to the default values. Correct operation of this function has been resolved, including the resetting of the serial control port back to default conditions (RS-232, 9600 baud, 8 data bits, 1 stop bit, no parity, no flow control).
New features:1. Advanced front panel control (Executive Mode command update). A functional change has been made regarding user access to certain advanced set-up and control features that are available from the front panel. The advanced features can be enabled or view only (default). When enabled, advanced features can be accessed and adjusted through front panel control. When view only (default), advanced features can be accessed but cannot be adjusted through front panel control.
Basic Features: (always available)
- Backlight on/off (hold inputs 1 and 2 buttons for 2 seconds to toggle)
- Audio Input gain/attenuation (hold Audio button down for 3 seconds)
- Making Ties
- Recalling and Saving Presets (press Preset button to recall or hold for 2 seconds to save)
- Executive Mode Command Changes (hold I/O or Enter+ I/O buttons for 2 seconds)

Advanced Features: (can be enabled or view only):
- RGB Delay (hold Video/RGBHV button for 3 seconds)
- I/O grouping (hold input 1 and output 1 buttons for 3 seconds)
- RS-232/422 port settings (hold all Control buttons for 3 seconds)
- Audio output volume control (hold Audio button down for 3 seconds) Select an output
- Output Muting (In View mode, hold an output button 3 seconds to toggle)

Current modes of FPC operation:
- FPC operation = press and hold both the VIDEO and AUDIO I/O buttons for 2 seconds to toggle
mode between modes. The I/O buttons will flash two times to indicate the state change.
- 0X = All FPC functions available (Version 2.01 Default Condition)
- 1X = Only view mode available – no changes can be made
- Any attempt to control switcher flashes I/O buttons two times.

New mode of FPC operation in version 2.03:
- 2X = All basic FPC functions are available - Advanced Features are View only, no setting allowed (Mode 2X is the new version 2.03 Default Condition)
- FPC selection: Press and hold the VIDEO and AUDIO I/O buttons for 2 seconds to toggle between modes 2X and
- 1X. (Compatible with the current control method). The I/O buttons will flash two times. Press and hold I/O buttons VIDEO, AUDIO and the ENTER button for 2 seconds to toggle between 2X and 0X. The I/O and Enter buttons will flash two times.
When Executive mode is set (1X) VIDEO, AUDIO will flash two times when a front panel function other than View is performed.

2. Webpage new features:
- Under Control / Set and View Ties page, erasing tie(s) is now possible.
- Under Control / Global Presets page, when a preset is saved or renamed, the preset number box turns BLUE for reference.
- SIS “LS” command update for the CrossPoint 450 Plus models
- The “0LS” command allows the user to verify active sources by polling all inputs for valid sync signals. The unit will respond with a string of numbers, “0” if no signal is present and a “1” if there is a sync signal present at the input.
Installation steps:1. Download the firmware file.
2. Run the .exe file. This opens the Firmware Update program, creating a product named folder within which is placed the firmware file (x.S19).
3. Access the device internal web pages.
4. Select the Configuration tab.
5. On the Configuration page, click Firmware Upgrade on the left sidebar menu.
6. Click Browse. A Choose File window opens.
7. Navigate to the folder (created in 1g) where the firmware upgrade file is saved and select the file.
NOTES:
- Valid firmware files must have the file extension “.S19”. Any other file extension is not a firmware upgrade.
- The original factory-installed firmware is permanently available on the scaler. If the attempted firmware upload fails for any reason, the scaler automatically reverts to the factory-installed firmware.
8. Click Open .
9. Click Upload . While the firmware is uploading, the Upload button changes to “Uploading...” . When the uploading process is complete, the button changes back to Upload. The uploading may take a few minutes.

Operating system:
OS Independent