Extron DXP 168 HD 4K Matrix Switcher 1.01.0000-b003
Extron DXP 168 HD 4K Matrix Switcher driver from Extron for OS Independent
Extron DXP 168 HD 4K Matrix Switcher driver from Extron for OS Independent
File size:.............. 33.5 KB
Downloads:......... 528
Release date:...... 03 May 2016
Last update:........ 03 May 2016
Publisher review for Extron DXP 168 HD 4K Matrix Switcher 1.01.0000-b003:
Before install Extron DXP 168 HD 4K Matrix Switcher 1.01.0000-b003you should set a system restore point, to make sure you can rollback to your original driver in case you accidentally install another driver or select the driver for another version of the operating system.
Also, do not forget to check with our site as often as possible for new version of Extron DXP 168 HD 4K Matrix Switcher . We recommend to always use most recent version of a driver.
This package provides the necessary installation files of Extron DXP 168 HD 4K Matrix Switcher Firmware 1.01.0000-b003.Fixes:- Fixed Issue (originated in 1.00.0000-b005): HDCP notification. Changing the HDCP notification between Black and Green via Product Configuration Software (PCS) or Simple Instruction Set (SIS) commands does not take place until the output sink is hot plugged. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005): DXP 44 HD 4K and DXP 84 HD 4K user EDID locations. EDID assignment to or from user loaded slots 5-8 is not available. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005): LPCM 5.1 and Dolby ATMOS. LPCM 5.1 and Dolby ATMOS only passes through the matrix when the Output Format is set to Pass Through. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005): Displays connected DXP HD 4K unable to go to standby - In rare cases, display devices such as computer monitors connected to matrix outputs were prevented from going to standby mode even when no matrix ties to the displays are made. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005): Extracted S/PDIF. Extracted S/PDIF audio is not muted when any HBR (High Bit Rate) audio stream is detected.This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005): No displayed image when a source with Display Port-HDMI adapter is connected. Intermittently no image is delivered to sink devices when a source with Display Port - HDMI adapter is connected to the matrix with an existing tie to sink devices. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005). DXP 44 HD 4K, DXP 84 HD 4K and DXP 88 HD 4K HDMI Output Format. Unable to set the HDMI output format without a connected sink device. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005). Mode 5 reset did not reset HDCP notification - After a Mode 5 reset, the DXP HD did not reset the HDCP notification back to default (green). This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005). Updated Copyright year. The Copyright year in the DXP HD internal webpage is 2015 instead of 2016. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005). Blocky image with some consumer displays when video format it set to Auto. In rare case, the DXP HD would output a blocky image when output video format was set to auto or full. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005). Delayed response after receiving non-applicable SIS command. The DXP HD 4K would stop responding to any subsequent SIS command for about a minute after receiving invalid command [Esc]IAFMT[CR]. This issue has been resolved.
- Fixed Issue (originated in 1.00.0000-b005). No audio after hot plugging the HDMI output of DXP 88 HD 4K. Intermittently no audio was heard from an audio receiver that’s connected to the DXP HD 4K output when the HDMI cable between the two is reseated. This issue has been resolved.
- Improved Feature. Improved DXP 44 HD 4K and DXP 88 HD 4K software load times. When connecting the Product Configuration Software (PCS 3.5.0 and above) to DXP 44 HD 4K or DXP 84 HD 4K, the amount of time it takes the software to load the existing configuration from the matrix has been improved.
- Improved Feature: Switching speed. Improved the switching speed between inputs.
- Improved Feature: Cooling Fan. Cooling fan speed has been improved to run more efficiently.
Installation steps:1. Download the .exe file and run it to extract the firmware.
2. Open the Internal Web Page of the Device.
3. Click the Update button in the Device Info panel. The Firmware Update dialog box opens.
4. Click the Browse button. The File Upload dialog box opens.
5. Navigate to the location of the firmware file. Valid firmware files have an .eff extension.
6. Select the file and click the Open button. The File Upload dialog box closes.
7. Click the Upload button. The Firmware Update dialog box closes.
8. Wait until the update it's complete.
Operating system:
OS Independent
